Preview Canon Printers and Multifunction PIXMA MX492 User's Manual Page 900 Online and Download PDF Manuals & Instructions for FREE from Manualagent.com.

• MX 900 Series Installation Guide. • VeriFone, the VeriFone logo, and Ruby SuperSystem are registered trademarks of VeriFone, Inc. Sapphire, Topaz, HPV-20, Ruby Manager, Everest, E ID, Electronic Journal On-site, and Ruby Card are trademarks of VeriFone, Inc. And/or other countries.

All other trademarks or brand names are the properties of their respective holders. • Contents 1. Introduction.1 Intended Audience.1 Document Organization. • MX 900 Series Installation Guide Cleaning the Terminal.25 Cleaning the Display Screen.. Cheats For Final Fantasy Tactics Advance Gameshark Codes.

25 Magnetic Stripe Cleaner. • MX 900 Series terminals, the MX 915 and MX 925 Intended Audience This guide is useful for anyone installing and configuring the MX 900 Series terminals. A basic description of terminal features is also provided. Document Organization The following chapters are included: Chapter 1, Introduction, explains the Intended Audience, Document Organization, and common acronyms, abbreviations, and definitions used.

• MX 900 Series Installation Guide Acronyms, Abbreviations, and Definitions The following table describes the common acronyms, abbreviations, and definitions used: Convention Meaning Buffer Flush Interval bits per second Cyclic Redundancy Check File Authentication Firmware Software in FLASH/ROM File Transfer Protocol. • ARDWARE NSTALLATION This chapter describes the MX 900 Series installation procedures and includes connection examples. Installing the Device This section presents installation guidelines for the MX 900 Series terminal. Unpacking Open the shipping carton and carefully inspect the contents for possible tampering or shipping damage. Select a location for the terminal that offers adequate ventilation and protection and is convenient for the user and merchant. Place the MX 900 Series terminal on a flat surface, such as a table or countertop, or mount it on a mounting stand supplied by VeriFone.

Avoid areas with: –. • MX 900 Series Installation Guide Warning: Do not use the MX 900 Series terminal near water, including a bathtub, wash bowl, kitchen sink, or laundry tub. Do not use in a wet basement or near a swimming pool. Before connecting the terminal to the power pack, complete the installation by connecting all the cables (see Connecting the Device and Power Up with the Multiport Cable). Darkstar One English Patch 1.3. • MX 900 Series Installation Guide Wall Mount The MX 900 Series terminal can be mounted on a wall.

To wall mount the MX 900 Series terminal: 1. Create a template of the three key hole slots on the bottom of the MX 900 Series terminal.

• Install so that customer is Stand Needed between PED and next in queue VeriFone also recommends instruction of the cardholder regarding safe PIN-entry. This can be done with a combination of: Signage on the PED ■ Prompts on the display, possibly with a “click-through” screen ■. • Installing Countertop Wedge The countertop wedge raises the rear section of the MX 900 Series terminal by an angle of 10 degrees to facilitate use of the screen. See the Stand Mount section for aligning the pins. • MX 900 Series Installation Guide Removing or Installing the I/O Module Use the following steps to remove and install I/O modules.

Tabs Tabs Push down the two tabs so that the I/O module can slide out. March 1, 2012. • Follow the steps below to install smart cards (MSAM or SD cards). Often merchants are issued MSAM or SD cards to run small applications, such as loyalty programs. MSAM and SD cards are used only with MX 900 Series terminal smart card configurations.

• MX 900 Series Installation Guide 3. Remove the card compartment door screw and rotate the door up and back to access the SD and MSAM cardholders. Remove any previously installed MSAM or SD card by sliding the card from the cardholder. • MX 900 Series Installation Guide Note: Before inserting the SD or MSAM card, position it with the card’s gold contacts facing the smart card reader end of the terminal. The cardholder connector base has a set of contacts and a notch on one corner to ensure the card is positioned correctly.

• MX 900 Series Installation Guide 6. Reinstall the compartment cover and door screw. March 1, 2012. • Installing the Stylus and Holster Use the following steps to install the stylus and its holster. Turn the MX 900 Series terminal over and plug the stylus cable into the top of the terminal and insert and tighten screw. • MX 900 Series Installation Guide 2. Locate the two screw holes for attaching the holster.